RCU Forums
0 2020/03/01 17:03:10
0 2020/03/01 17:03:24
0 2020/03/01 17:03:31
0 2020/03/08 21:11:57
If I had thought about it in time I would have taken a shot from up on a ladder straight down on the jig. I did try to get a straight above as I could for these 2 shots
If I had thought about it in time I would have taken a shot from up on a ladder straight down on the jig. I did try to get a straight above as I could for these 2 shots
0 2020/03/08 21:12:04
0 2020/03/09 09:20:51
0 2020/03/09 09:20:57
0 2020/03/09 09:21:03
0 2020/03/09 19:26:12
0 2020/03/09 19:26:37
0 2020/03/09 19:28:17
I'm going to have to make some new formers. I forgot that I made the fuse wider so the 10 oz fuel tank would fit between former #2's sides
I'm going to have to make some new formers. I forgot that I made the fuse wider so the 10 oz fuel tank would fit between former #2's sides
0 2020/03/09 19:28:27
0 2020/03/09 19:28:43
3 small pieces makes a whole vertical fin
3 small pieces makes a whole vertical fin
0 2020/03/09 19:29:01
See, a whole vertical fin the cheap way
See, a whole vertical fin the cheap way
0 2020/03/09 19:29:19
How I jigged the front fuse and the new rear section
How I jigged the front fuse and the new rear section
0 2020/03/09 19:29:46
0 2020/03/10 18:04:35
0 2020/03/11 20:47:07
0 2020/03/11 20:47:12
0 2020/03/11 20:47:19
24" handle because that is the length of the bar to start with, No way did I want to do any extra cutting of this stuff
24" handle because that is the length of the bar to start with, No way did I want to do any extra cutting of this stuff
0 2020/03/14 18:28:13
0 2020/03/14 18:28:18
I may make another torque rod a bit longer with longer arms. This seems a bit small looking at it now.
I may make another torque rod a bit longer with longer arms. This seems a bit small looking at it now.
0 2020/03/14 18:28:23
The backing bar (left) has slots cut in it so it can be adjusted for different sizes of wire. The bolt closest to the bottom of the pic is the pivot pin. The wire bends around it. The bolt just above and right is the bolt that actually bends the wire It has to go below the top of the base so I used a Fostner drill bit and wood chisel to re-leave a slot for it in the base.
The backing bar (left) has slots cut in it so it can be adjusted for different sizes of wire. The bolt closest to the bottom of the pic is the pivot pin. The wire bends around it. The bolt just above and right is the bolt that actually bends the wire It has to go below the top of the base so I used a Fostner drill bit and wood chisel to re-leave a slot for it in the base.
0 2020/03/14 18:28:30
You can see the slot for the bending bolt. the bolt needs to go below the base to get flat bends. With sturdier construction so the was no play in the handle the slot might not be needed The hole at the top bend is tapped for a 1/4 20 bolt, This is the pivot.
You can see the slot for the bending bolt. the bolt needs to go below the base to get flat bends. With sturdier construction so the was no play in the handle the slot might not be needed The hole at the top bend is tapped for a 1/4 20 bolt, This is the pivot.
0 2020/03/14 18:28:36
Came out EXACT!
Came out EXACT!
0 2020/03/14 18:28:44
0 2020/03/14 18:28:52
I may make another torque rod a bit longer with longer arms. This seems a bit small looking at it now.
I may make another torque rod a bit longer with longer arms. This seems a bit small looking at it now.
0 2020/03/14 19:18:20
The backing bar (left) has slots cut in it so it can be adjusted for different sizes of wire. The bolt closest to the bottom of the pic is the pivot pin. The wire bends around it. The bolt just above and right is the bolt that actually bends the wire It has to go below the top of the base so I used a Fostner drill bit and wood chisel to re-leave a slot for it in the base.
The backing bar (left) has slots cut in it so it can be adjusted for different sizes of wire. The bolt closest to the bottom of the pic is the pivot pin. The wire bends around it. The bolt just above and right is the bolt that actually bends the wire It has to go below the top of the base so I used a Fostner drill bit and wood chisel to re-leave a slot for it in the base.
0 2020/03/14 19:18:27
You can see the slot for the bending bolt. the bolt needs to go below the base to get flat bends. With sturdier construction so the was no play in the handle the slot might not be needed The hole at the top bend is tapped for a 1/4 20 bolt, This is the pivot.
You can see the slot for the bending bolt. the bolt needs to go below the base to get flat bends. With sturdier construction so the was no play in the handle the slot might not be needed The hole at the top bend is tapped for a 1/4 20 bolt, This is the pivot.
0 2020/03/14 19:18:33
0 2020/03/14 19:18:38
0 2020/03/14 19:18:46
24" handle because that is the length of the bar to start with, No way did I want to do any extra cutting of this stuff
24" handle because that is the length of the bar to start with, No way did I want to do any extra cutting of this stuff
0 2020/03/14 19:18:53
0 2020/03/14 19:18:58
2 projects underway at the same time
2 projects underway at the same time
0 2020/03/15 16:52:32
0 2020/03/15 16:52:37
I did this yesterday. That'l hold 'em in there!
I did this yesterday. That'l hold 'em in there!
0 2020/03/15 16:52:42
0 2020/03/15 16:52:48
0 2020/03/19 19:14:46
0 2020/03/19 19:15:03
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.