RCU Forums
jewellers peg board for solder work.
jewellers peg board for solder work.
0 2021/01/24 07:29:10
Will use PE for the handles
Will use PE for the handles
0 2021/01/24 07:41:51
Weld lines on the Trumpeter 1/16 Panther, very fine detail almost smooth.
Weld lines on the Trumpeter 1/16 Panther, very fine detail almost smooth.
0 2021/01/24 07:41:54
Loops , post handle to tube and used a burr to enhance the welds/armour plates.
Loops , post handle to tube and used a burr to enhance the welds/armour plates.
0 2021/01/25 14:46:43
Track hangers in brass , better than the tracks with the kit .
Track hangers in brass , better than the tracks with the kit .
0 2021/01/25 14:46:45
Tow cable and tracks fitted , need some more small chain for the track hanger pins.
Tow cable and tracks fitted , need some more small chain for the track hanger pins.
0 2021/01/25 14:46:47
Just had enough brass strip 0.5 by 2.5 mm to complete the hangers. Every time i looked for Schumo hangers they were out of stock.
Just had enough brass strip 0.5 by 2.5 mm to complete the hangers. Every time i looked for Schumo hangers they were out of stock.
0 2021/01/27 04:26:39
Forgot to fish the tow post out of white vinegar ,turned black overnight.
Forgot to fish the tow post out of white vinegar ,turned black overnight.
0 2021/01/27 04:26:44
Found an Aber mg cover from the KT set and very fine chain.
Found an Aber mg cover from the KT set and very fine chain.
0 2021/01/27 04:26:59
The tow wire needs to be set to shape , very stiff wire from chandlers
The tow wire needs to be set to shape , very stiff wire from chandlers
0 2021/01/27 04:27:15
The jig for the track hangers compared to the Tamiya setup.
The jig for the track hangers compared to the Tamiya setup.
0 2021/01/27 04:27:16
0 2021/01/31 15:11:42
Styrene card to make plate at rear same width as the armour interlock on front.
Styrene card to make plate at rear same width as the armour interlock on front.
0 2021/02/01 05:30:30
Cut to shape , a plus is that the rear plate is held tight against the engine deck without using the Tamiya screw fitting.
Cut to shape , a plus is that the rear plate is held tight against the engine deck without using the Tamiya screw fitting.
0 2021/02/01 05:32:29
Front light , need to centre the wire against the light fitting . Used a pre wired smd led as they have fine wires
Front light , need to centre the wire against the light fitting . Used a pre wired smd led as they have fine wires
0 2021/02/01 05:34:54
Chain retainer for the covers.
Chain retainer for the covers.
0 2021/02/01 05:38:59
Steel mesh.
Steel mesh.
0 2021/02/02 10:11:51
Cut and fitted.
Cut and fitted.
0 2021/02/02 10:11:54
The ring round the mesh to Finnish off.
The ring round the mesh to Finnish off.
0 2021/02/02 10:11:57
Brass ring for the fan cover.
Brass ring for the fan cover.
0 2021/02/04 04:47:39
Trimmed the mesh for a better fit.
Trimmed the mesh for a better fit.
0 2021/02/04 04:48:44
The metal surround just looks the part.
The metal surround just looks the part.
0 2021/02/04 04:49:43
Tracks fitted and chained pins to secure. Styrene round screen , the real on has a lip to hold the screen.
Tracks fitted and chained pins to secure. Styrene round screen , the real on has a lip to hold the screen.
0 2021/02/04 04:51:59
Brass is easier to replicate scale, plastic or 3D is far too thick and easy to break.
Brass is easier to replicate scale, plastic or 3D is far too thick and easy to break.
0 2021/02/04 04:52:47
0 2021/02/04 04:56:17
The Taigen PE screens are not very good , most images of the screens show that they have larger spaces in the mesh.
The Taigen PE screens are not very good , most images of the screens show that they have larger spaces in the mesh.
0 2021/02/04 04:56:33
Starter handle will be in a slighty different position due to the convoy light being further over. I like the reflector, will use a red led .
Starter handle will be in a slighty different position due to the convoy light being further over. I like the reflector, will use a red led .
0 2021/02/05 08:02:06
The bar? and lower bracket.
The bar? and lower bracket.
0 2021/02/05 08:05:50
Ready for the tools.
Ready for the tools.
0 2021/02/05 08:06:40
Tools fitted , can be removed for running outside.
Tools fitted , can be removed for running outside.
0 2021/02/05 08:07:32
Rear convoy and led for reflector.
Rear convoy and led for reflector.
0 2021/02/09 07:41:58
0 2021/02/11 05:36:55
Old servo used for turret motor with a large gear for a slower turn.
Old servo used for turret motor with a large gear for a slower turn.
0 2021/02/23 05:28:08
Brass rack and the barrel cleaning tube removed just the support left.
Brass rack and the barrel cleaning tube removed just the support left.
0 2021/02/23 05:29:33
Tow cable clamps and added styrene for scale armour.
Tow cable clamps and added styrene for scale armour.
0 2021/02/23 05:30:45
Track hangers and rack for hammer ,bar and crowbar
Track hangers and rack for hammer ,bar and crowbar
0 2021/02/23 05:31:34
Jack block and rack
Jack block and rack
0 2021/02/23 05:33:21
Track cable holder
Track cable holder
0 2021/02/23 06:03:03
0 2021/10/23 13:17:07
Old motor
Old motor
0 2021/10/27 14:18:59
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.